- Genuine German-made Lubing drinker cup, the cup used on every Dine-A-Chook cup drinker
- Original Lubing float fitted, with a pink Dine-A-Chook upgrade float in the bag
- Swap in the upgrade float for a higher, always-visible water level: a minute with pliers
- Screws into any Dine-A-Chook drinker or outlet: standard 1/8” BSPF thread
- For low-pressure, gravity-fed systems only
- 12-month warranty on Lubing cups. $22.95 flat delivery NZ-wide, any size order
- Genuine Lubing cup, made in Germany
- Pink upgrade float in the bag
- Fits every Dine-A-Chook cup drinker
- $22.95 flat delivery NZ-wide
The genuine replacement cup for your Dine-A-Chook drinker
This is the genuine German-made Lubing drinker cup used on every Dine-A-Chook cup drinker, supplied on its own for maintenance and repairs. If a cup has been dropped, chewed, split at the collar or simply worn out, this is the part: it screws straight into the same thread, and you never need to replace the drinker. It comes the way Lubing builds it, original float fitted, with a pink Dine-A-Chook upgrade float in the bag.
How the cup works
A float sits in the cup. As your birds drink and the level drops, the float drops with it and opens a small stainless valve that lets water in from the drinker. As the cup fills, the float rises and shuts the valve again. Nothing for the birds to press or peck, and nothing to learn. The cup holds only a little water at a time, so there is nothing for a hen to stand in, scratch litter into or foul the way she would an open dish.
The float in the bag is the upgrade, not a spare
For the higher water level it has to be swapped in.
Which float should I use?
Both floats refill the cup automatically. The difference is where they shut off: the original Lubing float closes the valve at a modest level, while the Dine-A-Chook upgrade float lets the cup fill a little higher first, so there is always more water in sight. Look closely and the only physical difference is a slightly thicker square pad where the float presses the valve. Most backyard keepers swap the upgrade in for the higher level, but the original works well too. With pliers, gently grasp the pin at the side of the cup and draw it halfway out; the float drops free. Hold the other float in place and push the pin home.
Float colours
Yellow, pink and blue upgrade floats are the same design and work identically, so colour is your preference only. Pink and blue stand out against the red cup, which makes a water check a glance from the coop door. Floats swap between any of our cups, and you can mix colours on one drinker. The same cup also comes with a yellow float or a blue float.
Would you rather it arrived ready to go?
The same cup is also sold with the pink upgrade float already fitted, so there is no swap to do.
What it fits, and where to mount it
The cup screws into a standard 1/8” BSPF thread, so it fits every upright Dine-A-Chook drinker, every drum drinker outlet and every automatic drinker frame, as well as our drum drinker fittings. Seat an O-ring on the thread first, then screw the cup in firmly by hand: snug, not forced.
Mount it higher than feels natural. Chickens find water by smell rather than by looking down into it, so the cup can sit right up at the smallest bird’s eye height. A cup mounted low catches every bit of litter and dust the flock scratches up, and that is the most common reason a cup fouls quickly.
Low pressure only
Lubing cups are made for low-pressure, gravity-fed systems. The water surface must sit no more than 35 cm above the cup; any higher and the valve cannot hold it back, and the cup overflows. That is a setup issue, not a fault. Mains or tank pressure needs a header tank to bring it down first.
A cup that drips or overflows is nearly always telling you one of four things: head pressure over 35 cm, an airlock in the reservoir (loosen the lid and listen for the hiss), grit on the valve seat, or that it is due for a clean. A weep at the thread is usually a flattened or nicked O-ring.
Looking after it
Rinse the cups when you refill. Every fortnight, or monthly at the least, strip the cup down (cup, float, pin and the two-part valve) and wash everything in warm soapy water. Never boiling water and never the dishwasher. Rain and tank water carry more sediment, so clean more often on those supplies.
Building your own drinker? Keep to the 35 cm rule and the cups will do their job. We are glad to share what we know, but we cannot fault-find a system we did not design or supply. Bought a complete Dine-A-Chook drinker? Then you have our full support: contact us and tell us what you have checked.
Specifications
| Cup | Genuine Lubing drinker cup, made in Germany |
|---|---|
| Thread | 1/8” BSPF |
| Size | 62 x 50 x 73mm (L x W x H), about 24g |
| Float fitted | Original Lubing float |
| In the bag | Pink Dine-A-Chook upgrade float |
| Use | Low-pressure, gravity-fed systems only (water surface no more than 35 cm above the cup) |
| Serves | 6–8 hens per cup |
12-month warranty on Lubing cups. Colour loss and fading, rodent damage, and cups used outside a low-pressure system or not installed as directed are not covered. Full terms on our warranty page. Delivery is a flat $22.95 NZ-wide, any size order.
Pairs well with
Lubing Cup O-Rings, 10 Pack
The seal where the cup screws in. Worth replacing a tired one when you change the cup.
View O-rings →Lubing Drinker Cups, 5 Pack
Five cups for a multi-cup drinker, or spares on the shelf.
View the 5 pack →Large Red Drinker, Twin Cup Pink Floats
The 4L red drinker with pink floats already fitted.
View the drinker →Product Specifications
- Compatibility:
- Fits genuine Dine-A-Chook chicken drinkers, drum outlets and automatic frames
- Thread Size:
- 1/8" BSPF
- Use Type:
- Low-pressure, gravity-fed systems only
- Included:
- 1 cup (original Lubing float fitted) + 1 pink Dine-A-Chook upgrade float
- Float Colour:
- Pink upgrade float included
- Size:
- 62 x 50 x 73mm, about 24g
- Country of Origin:
- Germany (Lubing)
- Warranty:
- 12 months (Lubing component)
$22.95 flat delivery NZ-wide, any size order. Delivery details →